Technical Resources & Support
Access validated technical documentation, processing guidance, and support resources for every Resinify Technology 3D printing resin — Technical Data Sheets (TDS), Safety Data Sheets (SDS), and Instructions for Use (IFU), plus printer compatibility, wavelength, layer thickness, wash and post-cure guidance, storage and shelf-life information, transport classification, and applicable regulatory or test standards, all sourced directly from each product's current documentation on file.
Dental Materials
High-precision dental model resin with crisp margins and fine detail.
| Printer compatibility |
DLP, mSLA |
| Wavelength |
405 nm |
| Layer thickness |
100 µm |
| Wash instructions |
Clean printed parts using 99% isopropyl alcohol according to the MD600/MD800 build and processing guide. |
| Post-cure instructions |
Validated cycles: Otoflash G171 (500 flashes, flip & repeat); PCA 4000 (1 min @ 20°C, 100%); PCA 2000 (2 min @ 20°C, 100%, flip & repeat); CUREbox Plus (5 min @ 30°C, flip & repeat); UVitron Intelliray 400 (15 sec @ 80%, flip & repeat). |
| Storage |
Dark, tightly closed original container, cool/dry/ventilated, away from sunlight and ignition sources. Freezes at 15°C (59°F). |
| Shelf life |
Approximately 1 year (storage stability) under proper storage conditions. |
| Transport classification |
US DOT / IMDG: UN 3082, Class 9, Packing Group III, Marine Pollutant: Yes. |
Fast-processing dental model resin for thermoforming, diagnostic and orthodontic appliance workflows.
| Printer compatibility |
DLP, mSLA |
| Wavelength |
405 nm |
| Layer thickness |
100 µm |
| Wash instructions |
Clean printed parts using 99% isopropyl alcohol according to the MD600/MD800 build and processing guide. |
| Post-cure instructions |
Validated cycles: Otoflash G171 (500 flashes, flip & repeat); PCA 4000 (1 min @ 20°C, 100%); PCA 2000 (2 min @ 20°C, 100%, flip & repeat); CUREbox Plus (5 min @ 30°C, flip & repeat); UVitron Intelliray 400 (15 sec @ 80%, flip & repeat). |
| Storage |
Tightly closed original container, cool/dry/ventilated, away from sunlight and ignition sources. Freezes at 15°C (59°F). |
| Shelf life |
Approximately 1 year (storage stability) under proper storage conditions. |
| Transport classification |
US DOT / IMDG: UN 3082, Class 9, Packing Group III, Marine Pollutant: Yes. |
Hybrid nanoceramic resin for permanent crowns, bridges, veneers and monolithic dentures.
| Printer compatibility |
DLP, mSLA |
| Wavelength |
385–405 nm |
| Wash instructions |
Clean in isopropyl alcohol >96% for a maximum of 5 minutes; dry with compressed air; clean again for a maximum of 2 minutes; air dry approximately 15 minutes before post-curing. |
| Post-cure instructions |
Otoflash G171 (2×3000 flashes, inert gas recommended); CUREbox Plus (2×25 min @ 50°C); Dreve PCU LED N₂ (18 min @ 90% under vacuum); iLuxCure Pro (10 min @ 100%); iLuxCure Dental (Program P08, 12 min @ 35%). |
| Storage |
5–30 °C in original bottle; protect from light; close tightly after use. |
| Shelf life |
Use before the expiration date shown on the bottle label. |
| Transport classification |
US DOT / IMDG: UN 3082, Class 9, Packing Group III, Marine Pollutant: Yes. |
| Regulatory / test standards |
ISO 20795-1, ISO 10993-1, ISO 10993-10 |
High-strength, biocompatible denture base resin for removable full denture bases.
| Printer compatibility |
DLP, LCD |
| Wavelength |
385–405 nm |
| Layer thickness |
50–100 µm |
| Wash instructions |
Wash twice in isopropyl alcohol >96%: first wash ≤5 minutes, second wash ≤2 minutes. |
| Post-cure instructions |
Otoflash G171 (2×3000 flashes under nitrogen); CUREbox Plus (2×25 min @ 50°C); Dreve PCU LED N₂ (18 min). |
| Storage |
10–30 °C; protect from light. |
| Shelf life |
24 months (unopened). |
| Transport classification |
Flash point >100 °C; not regulated as dangerous goods under DOT/ADR/RID/IMDG/IATA. |
| Regulatory / test standards |
ISO 10993, ISO 20795-1, REACH, RoHS |
Crystal-clear, biocompatible resin for nightguards, retainers and bite/stabilization/positioning splints.
| Printer compatibility |
DLP, mSLA |
| Wash instructions |
Two-stage isopropyl alcohol (>96%) clean — 5 min then 2 min, in a lab shaker (no ultrasonic bath), with gaps rinsed separately; air dry ~15 minutes before post-curing. |
| Post-cure instructions |
Initial post-cure: Otoflash G171 (2×1000 flashes, N₂ recommended); CUREbox Plus (2×5 min @ 45°C); Dreve PCU LED N₂ (18 min @ 90% under vacuum). Final post-cure (after polishing): Otoflash G171 (1000 flashes); CUREbox Plus (5 min @ 30°C); Dreve PCU LED N₂ (3 min @ 90% under vacuum). |
| Storage |
5–30 °C (41–86 °F) in original bottle; protect from light; close tightly after each use. |
| Shelf life |
Approximately 1 year (storage stability) under proper conditions; always confirm against the expiration date on the bottle label. |
| Transport classification |
US DOT / IMDG: UN 3082, Class 9, Packing Group III, Marine Pollutant: Yes. |
| Regulatory / test standards |
ISO 20795-2, ISO 10993-5, ISO 10993-10 |
Precision-grade, biocompatible resin for dental surgical guides and implant-placement accessories.
| Printer compatibility |
DLP, mSLA |
| Wavelength |
405 nm |
| Layer thickness |
50 µm |
| Wash instructions |
Post-process with isopropyl alcohol ≥99%. Use a dedicated resin tank, build platform, washing equipment and finishing kit for the biocompatible surgical-guide workflow. |
| Post-cure instructions |
Validated generic profile: 70°C for 30 minutes (exact cycle depends on curing unit used); cool to room temperature between cycles. |
| Storage |
Dark, tightly closed original container, cool/dry/ventilated, away from sunlight and ignition sources. Freezes at 15°C (59°F). |
| Shelf life |
Approximately 1 year (storage stability) under proper storage conditions. |
| Transport classification |
US DOT / IMDG: UN 3082, Class 9, Packing Group III, Marine Pollutant: Yes. |
| Regulatory / test standards |
ISO 20795-2, ISO 10993-5, ISO 10993-10, ISO 10993-1:2018 |
Tooth-colored temporary restorative resin for crowns, bridges up to seven units, inlays, onlays and veneers.
| Printer compatibility |
DLP, mSLA |
| Wavelength |
405 nm |
| Wash instructions |
Wash in a dedicated Resinify Wash Unit using isopropyl alcohol (IPA) ≥99%, with parts fully submerged. Avoid exceeding the wash duration, as this may affect dimensional accuracy and part performance over time. |
| Storage |
Product freezes at 15°C (59°F); thaw in a heated room up to 40°C (104°F) for 48 hours before use. Store away from heat, sparks, and open flame. |
| Transport classification |
US DOT / IMDG: UN 3082, Class 9, Packing Group III, Marine Pollutant: Yes. |
| Regulatory / test standards |
ISO 10993 (cytotoxicity), ISO 13485, ISO 14971 |
Wax-filled castable resin with rapid, clean, ash-free burnout and low thermal expansion, for precision dental and jewelry casting patterns.
| Printer compatibility |
DLP, mSLA |
| Layer thickness |
50 µm Z resolution (per IFU build orientation guidance) |
| Wash instructions |
Wash in 99% IPA using the High washing program for 3 minutes; do not exceed 5 minutes total alcohol exposure. Spray with fresh 99% IPA and clear with compressed air; air-dry 10 minutes before post-curing. |
| Post-cure instructions |
2 cycles of 50 flashes in a flash-curing unit, flipping models between cycles for an even cure. Models must be fully dry before post-curing. |
| Burnout guidance |
CastPro’s current documentation does not specify a burnout temperature schedule of its own. Follow your investment manufacturer’s burnout/casting instructions. |
| Storage |
10–40 °C in original container; store in a cool, dark, well-ventilated place protected from UV/sunlight. |
| Transport classification |
ADR/RID, IMDG and ICAO-TI/IATA-DGR: not classified as dangerous goods for land, sea, or air transport. |
Light-cured surface coating for a final glossy finish and protection of printed dental and photopolymer resin parts.
| Wavelength |
365–405 nm |
| Wash instructions |
Clean the printed part with 90–99% isopropyl alcohol before applying the glaze. |
| Post-cure instructions |
Use a UV/LED curing light ≥36 W at 365–405 nm. Cure approximately 60–90 seconds per side for dental parts; up to 2 minutes for larger parts or higher gloss. |
| Storage |
15–25 °C. |
| Shelf life |
12 months unopened; 6 months after opening. |
| Transport classification |
Not regulated as dangerous goods under DOT, IATA, or IMDG when shipped in small consumer quantities. |
| Regulatory / test standards |
ISO 10993-5 / -10 (formulated to comply, per TDS) |
Jewelry Casting Materials
Wax-filled castable resin for jewelry investment casting, filigree and micro-pavé designs, and small-batch production.
| Printer compatibility |
DLP, mSLA |
| Wavelength |
385–405 nm |
| Layer thickness |
50 µm baseline; 25 µm for very fine detail |
| Wash instructions |
Two-stage wash: 20–30 sec in fresh IPA or approved resin cleaner, then 20–30 sec in fresh IPA or TPM-type cleaner. Do not soak. Air-dry 10–15 minutes. |
| Post-cure instructions |
Low-temperature UV cure only: 5–10 minutes maximum under 405 nm UV; keep part temperature below 40°C. Avoid over-curing. |
| Burnout guidance |
Gypsum-bonded investment: ramp room temperature→300°C over 2 h; hold 300°C for 1 h; ramp to 730°C over 2 h; hold 730°C for 2 h. Pour at 500–600°C flask temperature, alloy dependent. For thick/solid parts extend the 300°C hold to 2 h; platinum may use an 850°C final burnout if the investment permits. |
| Storage |
18–28 °C; keep bottle closed and away from direct sunlight/excessive heat. |
| Transport classification |
ADR/RID, IMDG and ICAO-TI/IATA-DGR: not applicable; not a hazardous material for land or air transport. |
Fast-casting, zero-residue nano-wax resin for rings, pendants, earrings, and micro-detail or thin-walled jewelry components.
| Printer compatibility |
DLP, mSLA |
| Wavelength |
385–405 nm |
| Layer thickness |
50 µm baseline; 25 µm for ultra-high detail |
| Wash instructions |
Two-stage IPA wash: 20–40 sec first wash, then 15–20 sec in fresh IPA or resin cleaner. Do not soak. Air-dry 10–15 minutes. |
| Post-cure instructions |
Low-temperature UV cure: 5–10 minutes maximum; keep part temperature below 40°C to preserve clean burnout. |
| Burnout guidance |
Gypsum-bonded investment: ramp room temperature→300°C over 2 h; hold 300°C for 1 h; ramp to 730°C over 2 h; hold 730°C for 2 h. Cast at 500–600°C flask temperature depending on alloy. For thick pieces extend the 300°C hold to 2 h; platinum may use 850°C if the investment permits; avoid exceeding 900°C. |
| Storage |
18–28 °C; keep bottle sealed and away from sunlight and high heat. |
| Transport classification |
ADR/RID, IMDG and ICAO-TI/IATA-DGR: not applicable; not a hazardous material for land or air transport. |
High-detail castable resin for stone-setting designs, signet rings and bands, and large or heavy jewelry pieces.
| Printer compatibility |
DLP, mSLA |
| Wavelength |
385–405 nm |
| Layer thickness |
50 µm baseline; 25 µm for pavé |
| Wash instructions |
Two-stage wash: 20–30 sec in clean IPA, then 20–30 sec in fresh IPA or TPM cleaner. Do not soak longer than 1 minute. Air-dry 10–15 minutes. |
| Post-cure instructions |
Low-to-medium UV cure: 10 minutes recommended (5–15 min range); keep part temperature below 45°C. Avoid over-curing. |
| Burnout guidance |
Gypsum-bonded investment: ramp room temperature→300°C over 2 h; hold 300°C for 1 h; ramp to 730°C over 2 h; hold 730°C for 2–3 h. Cast at 500–600°C flask temperature. For heavy/thick models extend the 300°C hold to 2 h and the 730°C hold to 3–4 h; platinum may use 850°C if the investment permits. |
| Storage |
18–28 °C; keep resin covered and away from direct sunlight/excessive heat. |
| Transport classification |
ADR/RID, IMDG and ICAO-TI/IATA-DGR: not applicable; not a hazardous material for land or air transport. |
Precision casting resin with a smooth finish, for large rings, thick jewelry components and high-value alloy casting.
| Printer compatibility |
DLP, mSLA |
| Wavelength |
385–405 nm |
| Layer thickness |
50 µm baseline; 25 µm for high-detail patterns |
| Wash instructions |
Two-stage wash: 20–30 sec in fresh IPA, then 20–30 sec in clean IPA or TPM-style cleaner. Do not soak. Air-dry 10–20 minutes. |
| Post-cure instructions |
Moderate UV cure: 10–15 minutes; keep curing temperature below 50°C. Avoid over-curing. |
| Burnout guidance |
High-temperature cycle: ramp room temperature→300°C over 2 h; hold 300°C for 1 h; ramp to 730°C over 2 h; hold 730°C for 2–3 h. Cast at 500–650°C flask temperature. For large/thick patterns extend the 300°C hold to 2 h and the 730°C hold up to 4 h; optional 850°C hold for platinum if the investment permits. |
| Storage |
18–28 °C; keep away from direct sunlight and excessive heat; mix gently before use. |
| Transport classification |
ADR/RID, IMDG and ICAO-TI/IATA-DGR: not applicable; not a hazardous material for land or air transport. |
CastPro™ is validated for both dental and jewelry investment casting patterns — see the full CastPro resource card under
Dental Materials above.
Printer Compatibility & Settings
Exact settings vary by printer, resin, wavelength, and workflow. Rather than make a universal compatibility claim, we link you to each product's own validated documentation above — start with that product's Technical Data Sheet and Instructions for Use for the print and post-processing parameters that have actually been validated for it. If your printer or workflow isn't covered by the documentation on file, please contact us before assuming compatibility.
Need Technical Support?